We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks. Yükleniyor... I... IF it was the Slave unit on the cable, no further change for now.
My System Specs OS Windows 7 Pro 64-bit CPU Intel Core 2 Duo E7300 Motherboard Gigabyte GA-EP45-DS3L Memory Corsair TWINX 4096MB (2 x 2GB) Graphics Card Asus (ATI) Radeon 4670 HD Wonder what connects to where on the cable? Thanks for all your help, it at least brings back some confidence in my pc repair skills knowing I didn't spend the last few days just forgetting to do something stupid. Most modern CD drives are ATA33 while the modern hard drives are ATA133. read this article
Next, try this (on the basis that the optical unit is working OK). how can i reinstall windows when my dvd drive isn't detected? Abraham Levit 2.013.328 görüntüleme 7:46 Install a Hard Disk Drive, part 1: IDE drives - Süre: 9:18.
Login now. A wizard will pop up and walk you through this process. Any suggestions I can try would be fantastic because I am out of ideas. Hard Disk Not Detected In Bios Laptop If so, that would explain everything.
I tried to assign it a drive letter via right clicking, but all options were grayed out (meaning, not clickable). Bios Doesn't Detect Ide Hard Drive Now it should boot as it did before you ever opened the case. (This brings up the logical question of "Did you ever try to boot the computer before opening the The ribbon data cable should have 80 wires in it, even though the connectors only have 40 holes in them. pleas solved IDE Hard Disk and DVD writer comes up as Not Installed in the BIOS solved Hard Disk not getting detected after CHKDSK midway failure More resources See also solved
Keep the drive in the protective anti-static container until ready to install. How To Repair Hard Disk Not Detected Otherwise, check and consider changing every single entry... I dropped a second WDC hard drive in, formatted and was going to use it for a 2nd backup unit. This is where it goes bad.
The GREY one in the middle goes to the Slave device.4. http://ccm.net/forum/affich-29964-ide-cabel-hard-not-detect I have bought sata and installed xp on it. Detecting Ide Drives Problem Hakkında Basın Telif hakkı İçerik Oluşturucular Reklam Verme Geliştiriciler +YouTube Şartlar Gizlilik Politika ve Güvenlik Geri bildirim gönder Yeni özellikleri deneyin Yükleniyor... Çalışıyor... Detecting Ide Drives Error Solution This will stop any power saving commands from being sent.Turn on the system.
And there are some ways to partition the hard drive actually, say, partition the hard drive under Disk Management or use the third party partition manager tool like EaseUS partition Master Standard 40-pin ATA interface cable or an 80-conductor cable if running UATA66/100 (max length: 18 inches). Flag Permalink This was helpful (0) Collapse - Also check by billzhills / April 29, 2008 9:55 PM PDT In reply to: Problem IDE hard drives, not detected in bios The I'm not trying to get the files off it anymore im just trying to get one of the hdds to work on one of these computers so i can give it How To Connect Ide Hard Drive To Motherboard
Here's my problem: I installed Windows 7 Pro 64-bit on one of the partitions of the SATA HD. Internal Hard Disk Not Detected You cannot give a drive a letter; you can give a volume a letter. I don't remember what combination it was working till then.
All Rights Reserved. I guess I will just have to buy them a new computer. You cannot give a drive a letter; you can give a volume a letter. Ide Cable Bu tercihi aşağıdan değiştirebilirsiniz.
HDD The Guardian Series: Highly Specialized Internal Drives Rescue We Can Recover Your Files, Just in Case. Jul 31, 2010 #1 raybay TS Evangelist Posts: 7,241 +9 Time for a re-install, and look at your BIOS setups closely... Partition the drive. BEST TRICK - Süre: 7:46.
I actually see the IDE drive in disk drive (right-click Computer > properties > Device Manager > Disk Drives.) I've also attached two pictures of disk management window (where I described, Both of these... Uygunsuz içeriği bildirmek için oturum açın. A drive can only transfer as fast as the slowest device on the channel.
JRAtk94Jun 2, 2013, 9:41 PM Like I said, make sure that it's jumpers are set to "Master" and that it's connected to the "Master" ribbon connector. After typing the "list partition" this is what I see: I'm not sure what to do after that. EaseUS Partition Master, comprehensive hard disk partition tool and system optimization software for Windows-based administration, enables you to easily partition the hard disk or change/extend partition without data loss under Windows. Join the community here.
Click next it's just a summary of what you told it to do. Verify that the SATA drive is detected now. Thanks for the reply, I did initially just turn it on as it was and get into windows before I opened it up, basically it worked just fine. If both devices on the same IDE cable are set to master, you will have a problem.
The USB 3.0 port... Before I get into the problem, here's my HD configuration: 1 x 500GB SATA HD (2 partitions) -- Master Drive -- Windows 7 Pro 64-bit installed in one of the partitions If you're dual booting then Fat32 would probably be a good idea if the other OS can't read NTFS. How many devices do you have connected to the IDE (PATA) cable?